LED Strip Connector Cables & Accessories

Our range of LED Accessories include:

• Waterproof Cable Connectors (Silicone Gel)
• LED Hippo Connectors
• Fast Latch Spring Lever Connectors
• Heat Shrink Solder Connectors
• Jack Lead splitters
• Male jack connectors
• Female jack connectors
• Terminal Blocks
• Other accessories

Waterproof Gel Connectors

To make waterproof joints using terminal blocks or latch lever connectors we also stock a range of RayTech Waterproof connectors and connector covers. These simply clip together over the top of a joint and the gel filling covers and seals the joint making an IP68 rated connection. These can then be used underwater if needed.

These RayTech gel connectors are waterproof cable connectors IP68 that can be reused over and over again.

Latch Connectors

LED Technologies sell various connectors including:

• Push-on connectors that grip the strip firmly
• Latch Spring Lever connectors that are perfect for joining multiple cables of the same polarity together.

The wire/strip connector clips form a tight clamp on your electrical cables for your LED lighting installations. Sold individually for your convenience.

These are the perfect LED Strip light accessories, ideal for when you are connecting LED strips in parallel using the wire tails pre-soldered onto the strips.

HIPPO Connectors

Hippo Connectors by LED Technologies are a simple and easy way to securely connect LED strip to strip and LED strip to wire together. These hippo LED strip connectors help to speed up installation and are a new superior connector designed to replace the conventional Snap-On connectors.

Supplied in either Strip to Strip or Strip to Wire variations, there is a hippo connector suitable for most LED Strip installations.

Note: Once the connectors are closed they cannot be reopened due to the firm and tight connection.

Browse our range of Hippo Connectors to find the best secure strip connection for your project.

Cables

LED Technologies stock a large range of cables. There are cables to suit all of your installation projects. Our range of cables includes:

• Two core cable
• Four core cable
• Five core cable
• Six core cable
• 3 pin XLR male to female DMX Leads
• IEC leads

Our selection of power leads includes both round and flat (ribbon cable) versions. When selecting your cable for an installation, ensure that the correct one for your chosen LED fixture is picked. We have available extension cables for single colour, dual white and RGB LED strip variations.

We also stock 1M IEC power cables and 1.5m and 6m DMX cables to compliment your installation.

Solder Sleeves

Are you are looking for an easy and permanent solution for joining two cables together quickly and securely, making a soldered joint that is resistant to water ingress?

Our low temp solder heat shrink connectors are available in four different sizes to suit cable diameters from 0.25mm² to 6mm². Solder Seal Connectors otherwise known as Solder and Seal Wire Connectors are colour coded for easy size selection and are supplied in bags of 100.

These sleeves simply slide over the joint and using a heat gun will make a perfectly soldered waterproof joint every time without the need for a soldering iron.

1. Simply strip back the insulation from each of the two cables you want to join together.
2. After you have stripped the cables, slide the Solder and Seal Connector over one of the cables.
3. Twist the strands together or place them side by side and slide the connector back over the joint.
4. Take care to line up the solder ring with the conductors and then heat up the joint using a heat gun.

The solder ring will make a perfect soldered connection. The heat shrink section of the connector on each side of the joint will seal it onto the insulation making a strong, water-resistant joint.

The process takes less than a minute and all it requires is a heat gun. You do not need a soldering iron or solder as it’s all built into the Solder Seal Wire Connector.

Other accessories include:

• Male and female mini Jack Connectors
• Jack Plug Splitter Leads
• Jack Sockets
• Terminal Blocks
• Cable Ties
• LED strip connectors

We also have an excellent soldering iron kit that is supplied in a case. The kit includes various solder heads, a stand for the soldering iron, a roll of solder, tweezers and a solder sucker. This soldering set is ideal for soldering cables onto the cut points of your LED strip. The kit includes fine and angled soldering heads which are needed when soldering to four or five-channel LED strips.

For help and advice on our full range of accessories please contact our sales team by phone, email or using our live chat on the LED Technologies website.